- Mar 20, 2015
-
-
Henry authored
mixtureKEpsilon: Changed bounded non-conservative transport flux to be volumetric rather than mass-based Avoids numerical problems caused by large density gradients, particularly around the interface. Allows the use of higher-order differencing for km and epsilonm
-
Henry authored
Resolves bug-report http://openfoam.org/mantisbt/view.php?id=1579
-
- Mar 19, 2015
- Mar 18, 2015
- Mar 17, 2015
-
-
Henry authored
to avoid excessive pressure/buoyancy balance errors on non-orthogonal meshes Resolves bug-report http://openfoam.org/mantisbt/view.php?id=1379
-
Henry authored
Allows the specification of a reference height, for example the height of the free-surface in a VoF simulation, which reduces the range of p_rgh. hRef is a uniformDimensionedScalarField specified via the constant/hRef file, equivalent to the way in which g is specified, so that it can be looked-up from the database. For example see the constant/hRef file in the DTCHull LTSInterFoam and interDyMFoam cases.
-
- Mar 15, 2015
-
-
Henry authored
Resolves bug-report http://www.openfoam.org/mantisbt/view.php?id=1573
-
Henry authored
Avoids unnecessary increases in precision during intermediate steps for cases with adjustable time-step which may require very high precision to represent the time name.
-
- Mar 14, 2015
-
-
Henry authored
-
Henry authored
Add check for round-off error causing time reversal Resolves bug-report http://www.openfoam.org/mantisbt/view.php?id=815
-
- Mar 13, 2015
-
-
Henry authored
Disadvantage is that the BC values have to be specified in terms of hU rather than U. The alternative would be to add complex code to map h and U BCs into the equivalent for hU. Resolves bug-report http://www.openfoam.org/mantisbt/view.php?id=1566
-
Henry authored
-
Henry authored
Resolves bug-report http://www.openfoam.org/mantisbt/view.php?id=1568
-
Henry authored
Note that in order to build and install ParaView-4.3.1 lines 653-656 must be removed or commented from file ThirdParty-dev/ParaView-4.3.1/Qt/Components/CMakeLists.txt after unpacking the ParaView-4.3.1 source-pack from KitWare. This is because the file ui_pqExportStateWizard.h referred to in the lines 653-656: if(PARAVIEW_INSTALL_DEVELOPMENT_FILES) install(FILES "${CMAKE_CURRENT_BINARY_DIR}/ui_pqExportStateWizard.h" DESTINATION "${VTK_INSTALL_INCLUDE_DIR}") endif() does not exist and cannot be installed causing the build and installation to fail.
-
Henry authored
-
Henry authored
Resolves bug-report http://openfoam.org/mantisbt/view.php?id=1548
-
- Mar 11, 2015
-
-
Henry authored
Correction provided by Juho Peltola
-
Henry authored
Resolves bug-report http://www.openfoam.org/mantisbt/view.php?id=1563
-
- Mar 10, 2015
-
-
Henry authored
Revert changes in tutorial to correspond to the version in OpenFOAM-2.1.x Resolves bug-report http://openfoam.org/mantisbt/view.php?id=1207
-
Henry authored
-
Henry authored
Resolved bug-report http://www.openfoam.org/mantisbt/view.php?id=1564
-
- Mar 09, 2015
-
-
Henry authored
-
Henry authored
-
Henry authored
This approach simply accumulates data outside the range of the bins into the first or last bin which may be OK for small motions. For larger motions it may be better if the bins are updated or operate in a coordinate system attached to the body for solid-body motion. Resolves bug-report http://www.openfoam.org/mantisbt/view.php?id=1560
-
- Mar 08, 2015
-
-
Henry authored
-
Henry authored
Provided by Bruno Santos Also some general cleaning and update of comment. Resolves bug-report http://www.openfoam.org/mantisbt/view.php?id=1167
-
Henry authored
Resolves bug-report http://www.openfoam.org/mantisbt/view.php?id=815
-
Henry authored
-
Henry authored
Changes based on patches from and discussions with Bruno Santos Resolves bug-report http://www.openfoam.org/mantisbt/view.php?id=815
-